-- *****************************************************************
-- CISCO-PSA-MICROCODE-MIB.my
--
--
-- March 2002, Rishi K Mutnuru
--
-- Copyright (c) 2002 by Cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************
--
--CISCO-PSA-MICROCODE-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPEFROM SNMPv2-SMI
TEXTUAL-CONVENTION,TruthValueFROM SNMPv2-TC
MODULE-COMPLIANCE,NOTIFICATION-GROUP,OBJECT-GROUPFROM SNMPv2-CONF
entPhysicalIndex,entPhysicalDescr,entPhysicalName
FROM ENTITY-MIB
ciscoMgmt
FROM CISCO-SMI;ciscoPsaMicrocodeMIB MODULE-IDENTITYLAST-UPDATED"200206180000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134-1706
USA
Tel: +1 800 553-NETS
E-mail: gsr-netman@cisco.com"DESCRIPTION"Cisco PSA Microcode MIB - Overview
The PSA is the Packet Switching ASIC used
in module like engine 2(E2) line cards in GSR
for IP and MPLS packets forwarding. The PSA
performs IP and MPLS packet forwarding at 4 Mpps.
The list of features supported by the PSA
includes (but is not limited to):
- Input and Output ACLs
- Frame Relay Switching
- PIRC
- MPLS VPN
- BGP policy accounting
- IP packet coloring
- Sampled Net flow
- ATM over MPLS.
- Source MAC Accounting.
- Unicast RPF
Note that all the features are not
supported simultaneously on a module.
Each microcode bundle/set can support
one or a limited number of the features
listed above. Each feature has a priority.
When a feature (ACL, Sampled NetFlow) is
enabled through the CLI, the higher
priority feature will take precedence
over the lower priority feature. The
microcode for the lower priority is
removed and cleaned up. The higher
priority microcode will be loaded.
Later, if the higher priority feature
is removed, the lower priority microcode
will be loaded again.
This MIB contains information about the microcode
bundles on modules like E2 Line Cards(LC) in GSR.
Since microcode reload is a service interrupting
event, this MIB also defines a notification to
inform management stations that such an event has
taken place.
"REVISION"200206180000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 259}
-- Top-level structure of the MIBciscoPsaMicrocodeMIBNotifs OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIB 0}ciscoPsaMicrocodeMIBObjects OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIB 1}ciscoPsaMicrocodeMIBConformance OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIB 2}-- Subgroups:cpmcModulePsa OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIBObjects 1}cpmcBundle OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIBObjects 2}cpmcNotif OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIBObjects 3}-- Textual ConventionsPsaMicrocodeBundleId ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The identity of a PSA microcode bundle.
The current microcode bundles are:
unknown(1): Unknown Bundle. There will be
no entry associated with this
value in the cpmcBundleTable.
none(2): This value is used by
cpmcModulePsaPrevBundleId object
till the first micrcode reload
occurs on the psa. There will be
no entry associated with this
value in the cpmcBundleTable.
vanillaPOS(3): POS Vanilla
vanillaGE(4): GE Vanilla
vanillaInuit(5): Inuit Vanilla
vanillaTaz(6): TAZ Vanilla
pircPOS(7): POS Per Interface Rate Control
pircGE(8): GE Per Interface Rate Control
uRPFPOS(9): POS Unicast Reverse Path Forwarding
vrfSelectionPOS(10): POS VRF Selection
bgppaPOS(11): POS BGP Policy Accounting
bgppaGE(12): GE BGP Policy Accounting
ipColorPOS(13): POS IP Coloring
inputAcl128POS(14): POS 128 Line Input ACL
inputAcl128GE(15): GE 128 Line Input ACL
outputAcl128POS(16): POS 128 Line Output ACL
outputAcl128GE(17): GE 128 Line Output ACL
inputAcl448POS(18): POS 448 Line Input ACL
inputAcl448GE(19): GE 448 Line Input ACL
outputAcl448POS(20): POS 448 Line Output ACL
outputAcl448GE(21): GE 448 Line Output ACL
serverCard(22): Server Card
eoMplsGE(23): GE Ethernet over MPLS
frtpPOS(24): POS Frame Relay Traffic Policing
outputAclATM(25): ATM Output ACL
inputAcl128Taz(26): TAZ 128 Line Input ACL
vrfSelectionGE(27): GE VRF Selection
uRPFGE(28): GE Unicast Reverse Path Forwarding
cscGE(29): GE Carrier Supporting Carriers
linkBundleSMPOS(30): POS Link Bundle Single Mode
linkBundleDMPOS(31): POS Link Bundle Double Mode
linkBundleSMGE(32): GE Link Bundle Single Mode
linkBundleDMGE(33): GE Link Bundle Double Mode
"SYNTAXINTEGER{unknown(1),none(2),vanillaPOS(3),vanillaGE(4),
vanillaInuit(5),vanillaTaz(6),pircPOS(7),pircGE(8),uRPFPOS(9),vrfSelectionPOS(10),bgppaPOS(11),bgppaGE(12),ipColorPOS(13),inputAcl128POS(14),inputAcl128GE(15),outputAcl128POS(16),outputAcl128GE(17),inputAcl448POS(18),inputAcl448GE(19),outputAcl448POS(20),outputAcl448GE(21),serverCard(22),eoMplsGE(23),frtpPOS(24),
outputAclATM(25),inputAcl128Taz(26),vrfSelectionGE(27),uRPFGE(28),cscGE(29),linkBundleSMPOS(30),linkBundleDMPOS(31),linkBundleSMGE(32),linkBundleDMGE(33)}PsaMicrocodeFeatures ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The list of features supported on a PSA microcode
bundle.
The current list of features are:
basicIpForwarding(0): Basic IP Forwarding
basicMplsSwitching(1): Basic MPLS Switching
frameRelaySwitching(2): Frame Relay Switching
eAFrSwitching(3): Extended Addressing FR Switching
frtp(4): Frame Relay Traffic Policing
pirc(5): PIRC
vrfSelection(6): VRF Selection
uRPF(7): Unicast RPF
inputAcl128(8): 128 Line Input ACLs
outputAcl128(9): 128 Line Output ACLs
inputAcl448(10): 448 Line Input ACLs
outputAcl448(11): 448 Line Output ACLs.
sampledNetflow(12): Sampled Netflow
ipMarking(13): IP Marking
bgppa(14): BGP Policy Accounting
uti(15): Universal Transport Interface
mplsVpn(16): MPLS VPN
eoMpls(17): Ethernet over MPLS
atmoMpls(18): ATM over MPLS
csc(19): Carrier Supporting Carriers
multicast(20): Multicast
perPacketLoadBalancing(21): Per Packet Load Balancing
sourceMacAccounting(22): Source MAC Accounting
frSubVrf(23): FR per-subinterface VRF processing
serverCard(24): Server Card
mplsSNF(25): MPLS aware Sampled Netflow
linkBundle(26): Link Bundle
atomDisposition(27): AToM Disposition
"SYNTAXBITS{basicIpForwarding(0),basicMplsSwitching(1),frameRelaySwitching(2),eAFrSwitching(3),frtp(4),pirc(5),vrfSelection(6),uRPF(7),inputAcl128(8),outputAcl128(9),inputAcl448(10),outputAcl448(11),sampledNetflow(12),ipMarking(13),bgppa(14),
uti(15),mplsVpn(16),eoMpls(17),atmoMpls(18),csc(19),multicast(20),perPacketLoadBalancing(21),sourceMacAccounting(22),frSubVrf(23),serverCard(24),mplsSNF(25),linkBundle(26),atomDisposition(27)}cpmcModulePsaTable OBJECT-TYPESYNTAXSEQUENCEOF CpmcModulePsaEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table providing the microcode bundle information
of those modules which contains PSA (Ex: engine 2
line cards in GSR)."::={ cpmcModulePsa 1}cpmcModulePsaEntry OBJECT-TYPESYNTAX CpmcModulePsaEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Entries providing PSA microcode bundle information
of those entities of type PhysicalClass module(9)
and contain PSA."INDEX{ entPhysicalIndex }::={ cpmcModulePsaTable 1}
CpmcModulePsaEntry ::=SEQUENCE{
cpmcModulePsaCurrBundleId PsaMicrocodeBundleId,
cpmcModulePsaPrevBundleId PsaMicrocodeBundleId,
cpmcModulePsaFeaturesEnabled PsaMicrocodeFeatures,
cpmcModulePsaFeaturesDisabled PsaMicrocodeFeatures
}cpmcModulePsaCurrBundleId OBJECT-TYPESYNTAX PsaMicrocodeBundleId
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The identity of the microcode bundle currently
loaded on the PSA of the module identified by
entPhysicalIndex."::={ cpmcModulePsaEntry 1}cpmcModulePsaPrevBundleId OBJECT-TYPESYNTAX PsaMicrocodeBundleId
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The identity of the microcode bundle previously
loaded on the PSA of the module identified by
entPhysicalIndex. Till the first microcode reload
is performed on the module, the value will be
'none(2)'."::={ cpmcModulePsaEntry 2}cpmcModulePsaFeaturesEnabled OBJECT-TYPE
SYNTAX PsaMicrocodeFeatures
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The list of features newly enabled due to the
loading of the microcode bundle identified by
cpmcModulePsaCurrBundleId. "::={ cpmcModulePsaEntry 3}cpmcModulePsaFeaturesDisabled OBJECT-TYPESYNTAX PsaMicrocodeFeatures
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The list of features disabled because of the
unloading of microcode bundle identified by
cpmcModulePsaPrevBundleId and loading of the
microcode bundle identified by
cpmcModulePsaCurrBundleId."::={ cpmcModulePsaEntry 4}-- end of cpmcModulePsaTablecpmcBundleTable OBJECT-TYPESYNTAXSEQUENCEOF CpmcBundleEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of PSA microcode bundle features."::={ cpmcBundle 1}cpmcBundleEntry OBJECT-TYPESYNTAX CpmcBundleEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details the features of a microcode bundle."INDEX{ cpmcBundleId }
::={ cpmcBundleTable 1}
CpmcBundleEntry ::=SEQUENCE{
cpmcBundleId PsaMicrocodeBundleId,
cpmcBundleFeatures PsaMicrocodeFeatures
}cpmcBundleId OBJECT-TYPESYNTAX PsaMicrocodeBundleId
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The identity of the PSA microcode bundle. This
object value can't be unknown(1) or none(2)."::={ cpmcBundleEntry 1}cpmcBundleFeatures OBJECT-TYPESYNTAX PsaMicrocodeFeatures
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The list of features supported by microcode bundle
identified by cpmcBundleId."::={ cpmcBundleEntry 2}-- End of TablecpmcNotifEnables OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable indicates whether the system
produces the ciscoPsaMicrocodeReload notification.
A false value will prevent PSA microcode reload
notifications from being generated by the system."DEFVAL{ false }::={ cpmcNotif 1}ciscoPsaMicrocodeReload NOTIFICATION-TYPE
OBJECTS{
entPhysicalName,
entPhysicalDescr,
cpmcModulePsaCurrBundleId,
cpmcModulePsaPrevBundleId,
cpmcModulePsaFeaturesEnabled,
cpmcModulePsaFeaturesDisabled
}STATUScurrentDESCRIPTION"A ciscoPsaMicrocodeReload notification is generated
when a PSA microcode reload occurs.."::={ ciscoPsaMicrocodeMIBNotifs 1}-- conformance informationciscoPsaMicrocodeMIBCompliances OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIBConformance 1}ciscoPsaMicrocodeMIBGroups OBJECTIDENTIFIER::={ ciscoPsaMicrocodeMIBConformance 2}-- Compliances statementciscoPsaMicrocodeMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
the CISCO-PSA-MICROCODE-MIB."MODULE-- this moduleMANDATORY-GROUPS{
ciscoPsaMicrocodeParamsGroup,
ciscoPsaMicrocodeNotifGroup
}::={ ciscoPsaMicrocodeMIBCompliances 1}-- units of compliancesciscoPsaMicrocodeParamsGroup OBJECT-GROUP
OBJECTS{
cpmcModulePsaCurrBundleId,
cpmcModulePsaPrevBundleId,
cpmcModulePsaFeaturesEnabled,
cpmcModulePsaFeaturesDisabled,
cpmcBundleFeatures,
cpmcNotifEnables
}STATUScurrentDESCRIPTION"A collection of objects providing PSA microcode
monitoring."::={ ciscoPsaMicrocodeMIBGroups 1}ciscoPsaMicrocodeNotifGroup NOTIFICATION-GROUPNOTIFICATIONS{
ciscoPsaMicrocodeReload
}STATUScurrentDESCRIPTION"A collection of notifications generated by
the devices supporting this MIB."::={ ciscoPsaMicrocodeMIBGroups 2}END